>

WEAR PARTS & FILTERS

The parts a genset actually consumes in service - bearings, seals, service kits, couplings and filters. Every listing carries the OEM part number, the frame it fits and the brand it was built for, so you can match a part without sending the whole set back.

REQUEST A PART QUOTE

Find it by what failed, not by what it is called

Most part searches start with a symptom. These are the wear-part families we hold stock in, with the count of live listings behind each one. Send the part number or a photo of the failed part and we confirm the match before you order.

Bearings275
Service kits16
Terminal boards14
Couplings7
Anti-condensation heaters4

Rotors, stators, frames and complete generator ends are supplied against your nameplate rather than from stock - send the frame number, pole count and OEM number and we quote the assembly with lead time.

Three steps to the right part

Nine out of ten wrong-part shipments come from skipping step two. The part number is printed on the alternator, but it only identifies the family — the frame identifies the part.

STEP 1

Read the alternator nameplate

The nameplate on the alternator frame carries the model (for example P7C, UC27, F8) and the serial. Photograph it in daylight with the whole plate in frame — the model line is usually stamped rather than printed, and flash washes it out.

STEP 2

Confirm the frame and the pole count

A stator for a 4-pole F7 will not fit a 6-pole F7, and a bearing for a single-bearing machine will not fit a two-bearing one. Frame plus pole count plus bearing arrangement narrows 700 listings down to a handful.

STEP 3

Match the OEM number

Our listings carry the OEM number in the title — 45-0812, A062T497, 334-D111C12T000. If the number on your old part matches the listing, the part matches. If it does not, send us the old number and we cross-reference it.

Brands we hold parts for

Wear parts are listed against the alternator frame; consumables are listed against the engine. A Cummins engine can drive a Stamford alternator, and the two catalogues are separate.

Alternator frames we service

  • Stamford — bearings, terminal boards, couplings, service kits
  • Jinjia Power — wear parts held for our own builds
  • Cummins — couplings and terminal boards
  • Newage / Leroy-Somer — cross-referenced by frame number

Engine consumables

  • Cummins · Perkins · Volvo · MTU
  • Weichai · SDEC (Shangchai) · Yuchai
  • Yangdong · Mitsubishi
  • Filters, separators, belts, gaskets, overhaul kits

Frequently Asked Questions

What is the difference between generator parts and alternator parts?

An alternator part belongs inside the alternator: stator, rotor, bearing, AVR, terminal board. A generator part can belong anywhere on the set: engine filters, radiator hoses, exhaust silencer packing, controller, transfer switch. Most suppliers use the two terms interchangeably, which is why part searches often land on the wrong page.

Do you sell single parts or only complete assemblies?

Single parts. A bearing, a terminal board, one heater cartridge. Sets are also available where the maker only releases them as a kit, but the listing says so rather than hiding it behind a kit price.

Are the parts genuine or aftermarket?

Both, and each listing says which. On a bearing or a stator the qualification that matters is the dimensional and insulation standard, not the box. Where a part is safety-related — a circuit breaker in a transfer switch, for example — we quote the certified original and say why.

How do I identify a part when the nameplate is unreadable?

Measure instead. Stator core length, bore diameter, rotor shaft diameter and the number of leads coming out of the terminal box will identify the frame in almost every case. Send those four numbers plus a photo of the terminal box and we narrow it from there.

What is the lead time on a part that is not in stock?

Stamford and Newage frame parts are typically two to three weeks from order, engine consumables three to seven days, and transfer switches two to four weeks depending on rating and pole count. The quote states the lead time per line rather than as a single number for the order.

Can you supply parts for a set you did not build?

Yes. Give us the alternator model and the engine model, and we quote against those rather than against our own bill of materials. What we cannot do is warrant a part we did not supply into a set we did not build, and we say that up front.