86-0769-89610677 / 86-13553838770 | info@jinjiadongli.com
Home > TRANSFER SWITCHES > 1AUSA2100F4C Series 185SE - ASCO | Automatic, 100 AMP
1AUSA2100F4C Series 185SE - ASCO | Automatic, 100 AMP
1AUSA2100F4C ASCO 100 A1AUSA2100F4C ASCO 100 A1AUSA2100F4C ASCO 100 A1AUSA2100F4C ASCO 100 A

1AUSA2100F4C Series 185SE - ASCO | Automatic, 100 AMP

1AUSA2100F4C

Status: IN STOCK, Same day shipping Worldwide available | Brand New, Certified Factory Original

Volume, OEM and project pricing available on request.

πŸ“ž Get a Quote:86-13553838770
← Back to products

Specifications

Catalog Number1AUSA2100F4C
SeriesASCO Series 185SE
Product TypeService Entrance Automatic Transfer Switch (ATS)
Ampere Rating100 A
Number of Poles2 Poles
Voltage Rating240V
Neutral ConfigurationSolid Neutral
Frequency50 / 60 Hz
EnclosureNEMA 1
Transition TypeOpen Transition
ControllerStandard DIP-switch
CertificationUL 1008 Listed
Applicable StandardNEC / NFPA 70 Article 702 (optional standby)
Generator CompatibilityTwo-wire automatic-start generators
ManufacturerASCO Power Technologies (Schneider Electric)
AvailabilityIN STOCK β€” same-day shipping, worldwide
ConditionBrand New, Certified Factory Original
Warranty1 Year

Product Overview

The ASCO Series 185SE adds service-entrance rating to the compact 185 platform, integrating the utility disconnect and the transfer mechanism in one listed enclosure for residential and light-commercial standby systems. This unit is rated 100 A, 240V, 2-pole, NEMA 1, open transition. Typical loads are a residential service panel, a small retail or office panelboard, a well pump, a sump pump or a light commercial kitchen β€” circuits where the entire load can be picked up at once and where a compact wall-mounted enclosure is an advantage. The NEMA 1 enclosure is intended for indoor installation in a dry, protected space such as a mechanical room or an electrical closet. Terminations and footprint. On the 185 platform the lugs take one conductor per pole from #8 AWG to 2/0 AWG, and the whole switch is a compact wall-mount box one person can hang: this is the size that sits beside a residential panel or in a small mechanical closet and never gets a second thought. 100 A is the standard North American dwelling service and the point where a whole house transfers at once, so the contacts and the neutral plate are sized for the full load rather than for a selected circuit. Service arrangement. Two-pole 120/240 V single-phase: two ungrounded conductors and a grounded neutral, the arrangement behind nearly every North American dwelling and behind small shops on a split-phase service. Only two poles switch, so a solid-neutral unit carries the grounded conductor straight through while a switched-neutral unit opens it β€” which is what you want when the generator is treated as a separately derived source and the neutral must be broken to keep the two grounding electrodes apart. Neutral configuration. The grounded conductor is solid: it runs straight through on a bolted neutral plate and is never opened. That is the correct choice when the transfer switch is not a separately derived source β€” the generator neutral is bonded to the same grounding electrode system as the utility, so the neutral is one continuous current-carrying conductor end to end and breaking it would serve no purpose. It is also the cheaper of the two arrangements and has one fewer set of moving contacts to inspect, which is why it is the default on most commercial retrofits where the existing service neutral is already bonded. Enclosure. The Type 1 cabinet is for indoor use in a dry, protected space β€” a mechanical room, an electrical closet, a plant room β€” where the only thing it has to keep out is incidental dust and the occasional touch. It is not rain-tight and not watertight: mounting one on an exterior wall, even under a soffit, invites water in through the door seam and the conduit knockouts, and the first sign is usually a rusted mechanism rather than a tripped breaker. If the switch has to live outdoors, the 3R version of the same rating is the one to order. Service-entrance rating. This is the SE version, which means the assembly is listed as service equipment in its own right: the utility disconnect and the transfer mechanism share one enclosure, and there is no separate main breaker or service disconnect ahead of it. Three things follow from that. The neutral bus is the service neutral and the main bonding jumper lands inside this enclosure, so the grounding electrode conductor terminates here rather than at a separate disconnect. The short-circuit current rating applies to the whole assembly, not just to the switch, and it has to be checked against the available fault current at the service point. And the utility will want to see the listing before they energise it β€” a standard transfer switch installed ahead of the service disconnect without an SE rating is a common inspection failure. What the extra cost buys is one enclosure, one set of terminations and one less place for a bonding error. Matching generator. At 240V with an 0.8 power factor this switch carries approximately 19 kW of load (100 A Γ— 240V Γ— 0.8 = 19.2 kW, single-phase two-wire). Size the standby generator so that its standby rating meets or exceeds that figure, and confirm the generator's two-wire automatic-start contacts are compatible with the transfer switch controller. Controller. The 185 platform uses a DIP-switch controller with factory-set pickup and dropout thresholds (198 V pickup, 187 V dropout on the normal source by default), a approximately 10-second transfer delay, a 5-minute return-to-utility stability window and a 2-minute unloaded cool-down before the generator is signalled to stop. Two-pole configuration. Both the hot and the neutral are switched, which is the normal choice for 120/240 V single-phase residential and light-commercial services and for any circuit derived from a separately derived source. Supply. Supplied as a genuine ASCO Power Technologies (Schneider Electric) unit, brand new and factory original, packed for export from our Dongguan warehouse. Ask us for the outline drawing, wiring diagram and data sheet for this exact catalog number.

Jinjia Power Equipment Co., Ltd | Address: No.737, Guanzhang Road, Liaobu Town, Dongguan, China

Phone: 86-13553838770 | 86-0769-89610677 | info@jinjiadongli.com

Jinjia Power, Quality Assured

Frequently Asked Questions

What is the 1AUSA2100F4C transfer switch rated for?

The 1AUSA2100F4C is rated 100 A at 240V, 2-pole. It is a Service Entrance Automatic Transfer Switch (ATS) built on ASCO Series 185SE.

What type of transfer switch is the 1AUSA2100F4C?

1AUSA2100F4C is a Service Entrance Automatic Transfer Switch (ATS) in the ASCO Series 185SE family with Open Transition.

Which generators can the 1AUSA2100F4C be used with?

The 1AUSA2100F4C is specified for Two-wire automatic-start generators. Match the switch ampere rating to the generator output current and confirm the voltage and pole configuration before ordering.

What controller does the 1AUSA2100F4C use?

The 1AUSA2100F4C uses Standard DIP-switch. The controller supervises the normal and emergency sources and drives the transfer sequence.

What enclosure does the 1AUSA2100F4C come in?

The 1AUSA2100F4C is supplied in NEMA 1. Confirm the enclosure rating against your installation environment, indoor or outdoor, before ordering.

Is the neutral on the 1AUSA2100F4C solid or switched?

The 1AUSA2100F4C is supplied with Solid Neutral. This matters on systems with ground fault protection, where a switched neutral is normally required.

What certifications and standards does the 1AUSA2100F4C meet?

1AUSA2100F4C is certified to UL 1008 Listed. It is designed and tested to NEC / NFPA 70 Article 702 (optional standby). Request the current certificate for your project file before submission.

How many poles does the 1AUSA2100F4C have?

The 1AUSA2100F4C is a 2-pole device. Pole count must match your distribution: single phase two wire, three phase three wire, or three phase four wire with neutral.

What frequency does the 1AUSA2100F4C operate at?

The 1AUSA2100F4C is rated for 50 / 60 Hz. Confirm the generator and the utility supply are on the same frequency before installation.

Who makes the 1AUSA2100F4C and what is the supply status?

1AUSA2100F4C is manufactured by ASCO Power Technologies (Schneider Electric). Current availability: IN STOCK β€” same-day shipping, worldwide. Condition: Brand New, Certified Factory Original. Warranty: 1 Year.